BT8376KPF
| Model | BT8376KPF |
| Description | single chip transceivers for T1/E1 and Integrated Service Digital Network (ISDN) primary rate interfaces |
| PDF file | Total 323 pages (File size: 2M) |
| Chip Manufacturer | CONEXANT |
Bt8370/8375/8376
Fully Integrated T1/E1 Framer and Line Interface
The Bt8370/8375/8376 is a family of single chip transceivers for T1/E1 and Integrated
Service Digital Network (ISDN) primary rate interfaces, operating at 1.544 Mbps or
2.048 Mbps. These devices combine a sophisticated framer, transmit and receive slip
buffers, and an on-chip physical line interface to provide a complete T1/E1 transceiver.
The fully featured Bt8370 and short-haul Bt8375 and Bt8376 devices provide a
programmable clock rate adapter for simplifying system bus interfacing. The adapter
synthesizes standard clock signals from the receive or transmit line rate clocks or from an
external reference.
Operations are controlled through memory-mapped registers accessible via a parallel
microprocessor port. Current ANSI, ETSI, ITU-T, and Bellcore standards are supported for
alarm and error monitoring, signaling supervision (e.g., LAPD/SS7), per-channel trunk
conditioning, and Facility Data Link (FDL) maintenance. A serial Time Division Multiplexed
(TDM) system bus interface allows the backplane Pulse Code Modulation (PCM) data
highway to operate at rates from 1.536 to 8.192 Mbps. Extensive test and diagnostic
functions include a full set of digital and analog loopbacks, PRBS test pattern generation,
BER meter, and forced error insertion.
The physical line interface circuit recovers clock and data from analog signals with +3 to
–43 dB cable attenuation, appropriate for both short (–18 dB) and long-haul T1/E1
applications. Receive line equalization (EQ) and transmit Line Build Out (LBO) filters are
implemented using Digital Signal Processor (DSP) circuits for reliable performance. Data
and/or clock jitter attenuation can be inserted on either the receive or transmit path. The
transmit section includes precision pulse shaping and amplitude pre-emphasis for cross
connect applications, as well as a set of LBO filters for long-haul Channel Service Unit
(CSU) applications. A complementary driver output is provided to couple 75/100/120
Ω
lines via an external transformer.
Distinguishing Features
•
Single-chip T1/E1 framer with
short/long-haul physical line
interface
Frames to popular T1/E1 standards:
– T1: SF, ESF, SLC
96, T1DM
– E1: PCM
-
30, G.704, G.706, G.732
ISDN primary rate
•
•
On-chip physical line interface
compatible with:
– DSX-1/E1 short-haul signals
– DS-1 (T1.403) and ETSI long-haul
signals
•
•
•
•
•
•
•
•
•
•
Functional Block Diagram
Two-frame transmit and receive PCM
slip buffers
Clock rate adapter synthesizes jitter
attenuated system clocks from an
internal or external reference
Parallel 8-bit microprocessor port
supports Intel or Motorola buses
Automated Facility Data Link (FDL)
management
BERT generation and counting
Two full-duplex HDLC controllers for
data link and LAPD/SS7 signaling
B8ZS/HDB3/Bit 7 zero suppression
80-pin MQFP surface-mount package
Operates from a single +5 Vdc ±5%
power supply
Low-power CMOS technology
Receive
Analog
RX
RPLL
EQ
ZCS
Decode
TX or RX
Jitter
Attenuator
ZCS
Encode
Overhead
Insertion
T1/E1
Receive
Framer
RX
Slip
Buffer
Receive
System
Bus
Applications
•
•
T1/E1 Channel Service Unit/Data
Service Unit (CSU/DSU)
Digital Access Cross-Connect
Systems (DACS)
T1/E1 Multiplexer (MUX)
PBXs and PCM channel bank
T1/E1 HDSL terminal unit
ISDN Primary Rate Access (PRA)
TPLL
Transmit
TX
Analog
Pulse
LBO
TX
Slip
Buffer
Transmit
System
Bus
T1/E1
Transmit
Framer
Clock Rate
Adaptor
•
•
•
•
JTAG
Control/Status
Registers
Data Link Controllers
DL1 + DL2
Test Port
Motorola/Intel
Processor Bus
Dual-Rail/NRZ/
External DL3
CLAD I/O
Data Sheet
N8370DSE
June 30, 1999
