F310G226MPE
| Model | F310G226MPE |
| Description | Tantalum Capacitor, Polarized, Tantalum (solid Polymer), 4V, 20% +Tol, 20% -Tol, 22uF, Surface Mount, 0805, CHIP, ROHS COMPLIANT |
| PDF file | Total 2 pages (File size: 122K) |
| Chip Manufacturer | NICHICON |
CONDUCTIVE POLYMER TANTALUM SOLID ELECTROLYTIC CAPACITORS
F31
Conductive Polymer Resin-molded Chip,
Compact Series
Adapted to the RoHS directive (2002/95/EC).
Specifications
Item
Performance Characteristics
Category Temperature Range –55 to +105˚C (Rated temperature + 85˚C)
Capacitance Tolerance
±20%
(120Hz)
Dissipation Factor(at 120Hz) Refer to the list below
ESR (100kHz)
Leakage Current
Ripple Current
Refer to the list below
After 5 minutes' application of rated voltage, leakage current
at 20˚C is not more than 0.1CV
Refer to the list below
Type numbering system (Example : 6.3V 47 µF)
1
2
3
4
5
6
7
8
9
10
11
At 60˚C, 90 to 95% R.H. 500hours
Damp Heat
Capacitance Change..Within –20 to +30% of initial value
(No voltage applied) Dissipation Factor.......1.5 times Initial specified value or less
Leakage Current.........Initial specified value or less
–55˚C / +105˚C 30 minutes each 5 cycle
Capacitance Change..Within
±20%
of initial value
Temperature Cycles
Dissipation Factor.......Initial specified value or less
Leakage Current.........Initial specified value or less
Resistance
to Soldering Heat
Test Condition;10 second reflow at 240˚C
Capacitance Change..Within
±20%
of initial value
Dissipation Factor.......1.3 times Initial specified value or less
Leakage Current.........Initial specified value or less
After application of surge voltage in series with a 1kΩ resistor
at the rate of 30 seconds ON, 30 seconds OFF, for 1000
successive test cycles at 85˚C, capacitors meet the
characteristics requirements listed below.
Capacitance Change...Within
±20%
of initial value
Dissipation Factor........Initial specified value or less
Leakage Current..........Initial specified value or less
After 1000 hours' application of rated voltage in series
with a 3Ω resistor at 85˚C.
Capacitance Change....Within
±20%
of initial value
Dissipation Factor...1.5 times Initial specified value or less
Leakage Current...Initial specified value or less
After 1000 hours' application of rated voltage in series
with a 3Ω resistor at 105˚C,capacitors meet the characteristic
requirements listed below
Capacitance Change....Within
±20%
of initial value
Dissipation Factor...3 times Initial specified value or less
Leakage Current...Initial specified value or less
After applying the pressure load of 5N for 10±1 seconds
horizontally to the center of capacitor side body which has
no electrode and has been soldered beforehand on an
aluminum substrate, neither exfoliation
not its sign shall be found at the terminal
5N (0.51kg
•
f)
For 10±1seconds
electrode.
Keeping a capacitor surface-mounted on a substrate upside
down and supporting the substrate at both of the opposite
bottom points 45mm apart from the center of the capacitor,
the pressure load is applied with a specified jig at the center
of the substrate so that the substrate may bend by 1mm as
illustrated.
20
R230
Then, there shall be found no
remarkable abnormality on the
capacitor terminals.
45
45
1mm
F 3 1 0 J 4 7 6 M B
A
Tape width Reel Dia Reel Dia
(mm)
(φ180mm)
(φ330mm)
A
E
8
Case code
Capacitance tolerance
Rated Capacitance
Rated voltage
Series
Surge
Dimensions
L
H
W
1
Endurance 1
W
2
S
Case code
P
A
B
S
(mm)
L
2.0
±
0.2
3.2
±
0.2
3.4
±
0.2
W
1
1.25
±
0.1
1.6
±
0.2
2.8
±
0.2
W
2
0.9
±
0.1
1.2
±
0.1
2.3
±
0.1
H
1.1
±
0.1
1.1
±
0.1
1.1
±
0.1
S
0.5
±
0.2
0.8
±
0.2
0.8
±
0.2
Endurance 2
Shear Test
Marking
P Case
A Case
B Case
Rated Capacitance (
µ
F)
Capacitance
Conductive
Polymer
Ja
Rated
Voltage
code
Capacitance
code
Jar
Rated
Voltage
code
code
Terminal Strength
33
P6v
Month code
Month
code
Conductive Polymer
Rated Voltage (6.3V is marked as "6V " )
CAT.8100W-2
