Q2004K31V
| Model | Q2004K31V |
| Description | Thyristor Product Catalog |
| PDF file | Total 224 pages (File size: 3M) |
| Chip Manufacturer | TECCOR |
AN1003
Application Notes
Permanent Magnet Motor Control
Figure AN1003.16 illustrates a circuit for phase controlling a per-
manent magnet (PM) motor. Since PM motors are also genera-
tors, they have characteristics that make them difficult for a
standard triac to commutate properly. Control of a PM motor is
easily accomplished by using an alternistor triac with enhanced
commutating characteristics.
Load
R1
SCR1
AC
Input
CR1
R2
2.2 k
+
DC
MTR
R3
1.5 A
3.3 k
Q4006LH4
250 k
100
MT2
AC
Input
Voltage
AC
Load
Current
-
R2
500 k
CR1
IN4003
SCR1
EC103B
R3
1k
Not
Required
1k
115 V ac
Input
15 k 1/2 W
G
HT-32
MT1
0.1
µF
400 V
120 V ac
60 Hz
120 V ac
60 Hz
240 V ac
60 Hz
240 V ac
60 Hz
240 V ac
50Hz
0.8 A
8.5 A
100 k
IN4003
S2010F1
0.1
µF
400 V
0.1
µF
100 V
0.8 A
1M
IN4004
EC103D
Not
Required
1k
Figure AN1003.16
Circuit for Phase Controlling a Permanent Magnet
Motor
8.5 A
250 k
1M
IN4004
S4010F1
PM motors normally require full-wave DC rectification. Therefore,
the alternistor triac controller should be connected in series with
the AC input side of the rectifier bridge. The possible alternative
of putting an SCR controller in series with the motor on the DC
side of the rectifier bridge can be a challenge when it comes to
timing and delayed turn-on near the end of the half cycle. The
alternistor triac controller shown in Figure AN1003.16 offers a
wide range control so that the alternistror triac can be triggered at
a small conduction angle or low motor speed; the rectifiers and
alternistors should have similar voltage ratings, with all based on
line voltage and actual motor load requirements.
2.5 A
IN4004
T106D1
Figure AN1003.17
Half-wave Control, 0° to 90° Conduction
Figure AN1003.18 shows a half-wave phase control circuit using
an SCR to control a universal motor. This circuit is better than
simple resistance firing circuits because the phase-shifting char-
acteristics of the RC network permit the firing of the SCR beyond
the peak of the impressed voltage, resulting in small conduction
angles and very slow speed.
Universal Motor
M
R1
3.3 k
D1
AC
Supply
R2
SCR Phase Control
Figure AN1003.17 shows a very simple variable resistance half-
wave circuit. It provides phase retard from essentially zero (SCR
full on) to 90 electrical degrees of the anode voltage wave (SCR
half on). Diode CR
1
blocks reverse gate voltage on the negative
half-cycle of anode supply voltage. This protects the reverse gate
junction of sensitive SCRs and keeps power dissipation low for
gate resistors on the negative half cycle. The diode is rated to
block at least the peak value of the AC supply voltage. The retard
angle cannot be extended beyond the 90-degree point because
the trigger circuit supply voltage and the trigger voltage produc-
ing the gate current to fire are in phase. At the peak of the AC
supply voltage, the SCR can still be triggered with the maximum
value of resistance between anode and gate. Since the SCR will
trigger and latch into conduction the first time I
GT
is reached, its
conduction cannot be delayed beyond 90 electrical degrees with this
circuit.
SCR1
CR1
HT-32
C1
AC
Input
Voltage
AC
Load
Current
R2
150 k
CR1
IN4003
SCR1
S2015L
C1
0.1µF 200 V
120 V ac
60 Hz
240 V ac
60 Hz
240 V ac
50 Hz
8A
6.5 A
200 k
IN4004
S4008L
0.1µF 400 V
6.5 A
200 k
IN4004
S4008L
0.1µF 400 V
Figure AN1003.18
Half-wave Motor Control
http://www.teccor.com
+1 972-580-7777
AN1003 - 6
©2002 Teccor Electronics
Thyristor Product Catalog
