QTS-125-01-C-D
| Model | QTS-125-01-C-D |
| Description | Board Connector, 250 Contact(s), 2 Row(s), Male, Straight, Surface Mount Terminal |
| PDF file | Total 3 pages (File size: 398K) |
| Chip Manufacturer | SAMTEC |
REVISION AA
DO NOT
SCALE FROM
THIS PRINT
QTS-XXX-XX-XXX-D-XXX
No OF POSITIONS
-025, -050, -075,
**-100, **-125
(PER ROW)
** (SEE NOTE 14)
LEAD STYLE
-01: .1680[4.267]
-02: .2861[7.264]
-03: .4043[10.269]
-04: .6001[15.246]
-05: .7181[18.240]
-06: .8361[21.237]
OPTION
-LC: LOCKING CLIPS (SEE NOTE 10 AND NOTE 15)
(USE LC-08-TM-01)
-A: ALIGNMENT PINS (SEE NOTE 10)
(USE QTS-25-XX-D-XX-A)
-K: POLYIMIDE FILM PAD
(USE K-DOT-.276-.375-.005, SEE FIG. 2)
-GP: GUIDE POST, SEE FIG. 4
(AVAILABLE ON STYLE -01 ONLY)
-TR: TAPE & REEL (75 POS MAX)
(N/A ON STYLE -05 & -06)
ROW SPECIFICATION
-D: DOUBLE (USE QTS-25-XX-D-XX
& QTSH-25-XX-D-XX )
No OF BANKS
= SEE SHEET 3
* = NOT TOOLED
C1
(No OF POSITIONS / 25) x .7875[20.003] REF
SEE NOTE 13
01
.7875 20.003 REF
*
*
.155 3.94 REF
(SEE NOTE 16)
02
.235 5.97
REF
.644 16.36 REF
24 EQ SPACES
@ .0250[.635]
"A"
PLATING SPECIFICATION
(SEE TABLE 5)
.0325 0.826 REF
QTS-25-XX-D-XX
.155±.003 3.94±0.076
.0080 0.203 REF
FIG 1
QTS-075-01-XXX-D-LC SHOWN
T-1S56-XX-XXX
"B" REF
C3
AA
"A"
.0550 1.397
(SEE NOTE 8, 9 & 12)
.003[.08]
.001[.03]
C2
SEE TABLE 2
(SEE NOTE 9 & 12)
.037 0.94 REF
.015 0.38 REF
NOTES:
.010 0.25 REF
"A"
.7450 18.923 REF
T-1G1-XX-XXX
LC-08-TM-01
.038 0.95 REF
.056 1.42 REF
.280 7.11 REF
(((No OF POSITIONS / 25) x .7875[20.003]) -.060[1.52]) .003[.08]
2 MAX SWAY
(TYP)
-LC: LOCKING CLIP OPTION SHOWN
QTS-25-XX-D-XX-A
.0375 0.953
REF
.0375 0.953
REF
R
.035 0.89 REF
((No OF POSITIONS / 25) x .7875[20.003]) - .060[1.52] REF
-A: ALIGNMENT PIN OPTION SHOWN
AA
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN INCHES.
TOLERANCES ARE:
.XX: .01[.3]
.XXX: .005[.13]
.XXXX: .0020[.051]
MATERIAL:
1.
C
REPRESENTS A CRITICAL DIMENSION.
2. DELETED.
3. DELETED.
4. MINIMUM TERMINAL RETENTION: 6 OZ.
5. MINIMUM GROUND PLANE RETENTION: 1 LB.
6. DELETED.
7. PARTS TO BE MOLDED TO POSITION.
8. MAXIMUM VARIANCE OF .002[.05].
9. DIMENSION APPLIES TO TERMINALS AND GROUND PLANES INDEPENDENT OF
THE GROUND PLANE OR TERMINAL RESPECTIVELY.
10. LEAD STYLES -03 AND -05: TOP BODY (QTS) CANNOT HAVE -A OPTION AND
-04 AND -06 CAN USE EITHER -A OR -LC BODY.
11. T-1SXX-XX-L CAN BE SUBSTITUTED FOR T-1SXX-XX-F.
12. GROUND PLANE PRESS HEIGHT MUST BE .003[.08] LESS THAN THE MAX
HEIGHT OR .001[.03] GREATER THAN THE MINIMUM HEIGHT OF THE TERMINALS.
13. WINDOW NOT PRESENT ON LEAD STYLES -02 THRU -06 HEIGHT
PER REV. E OF THE QTS-25-XX-D-XX-X-XX.
14. FOR NEWAPPLICATIONS REQUIRING THESE POSITIONS, PLEASE CONTACT SAMTEC
INTERCONNECT PROCESSING GROUP.
15. DUE TO THE HIGH AMOUNT OF INSERTION FORCE NEEDED, THE –LC
OPTION IS NOT COMPATIBLE WITH AUTO PLACEMENT. SAMTEC
RECOMMENDS MANUAL PLACEMENT FOR ALL ASSEMBLIES WITH THE –LC OPTION.
16. PIN CAN EXTEND PAST WALL .003 MAX.
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
SECTION "A"-"A"
DECIMALS
ANGLES
2
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733
FAX: 812-948-5047
e-Mail: info@SAMTEC.com
code: 55322
DESCRIPTION:
DO NOT SCALE DRAWING
SHEET SCALE: 1:0.666667
INSULATOR: LCP, COLOR: BLACK
TERMINAL: PHOS BRONZE
GROUND PLANE: PHOS BRONZE
F:\DWG\MISC\MKTG\QTS-XXX-XX-XXX-D-XXX-MKT.SLDDRW
H.635mm DOUBLE ROW HS TERMINAL ASSEMBLY
DWG. NO.
BY:
DEAN P
QTS-XXX-XX-XXX-D-XXX
09-14-2010
SHEET
1
OF
3
