• Inventory
  • Products
  • Technical Information
  • Circuit Diagram
  • Data Sheet
Data Sheet
Home > Data Sheet > V07E130L4B
V07E130L4B

V07E130L4B

Model V07E130L4B
Description Varistor, 170V, 12.5J, Through Hole Mount,
PDF file Total 11 pages (File size: 99K)
Chip Manufacturer RENESAS
UltraMOV Series
Model Number Nomenclature
The UltraMOV Series follows a different part numbering
procedure than other Harris Varistor products. The base part
number consists of the following:
V =
xx =
E =
xxx =
Harris Varistor Designation
Nominal Disc Diameter (07, 10, 14, 20mm)
Epoxy Encapsulation (Rated to 85
o
C)
V
M(AC) RMS
Voltage Rating (130V - 625V)
Terms
Rated AC Voltage (V
M(AC)RMS
)
This is the maximum continuous sinusoidal voltage which
may be applied to the MOV. This voltage may be applied at
any temperature up to the maximum operating temperature
of 85
o
C.
Maximum Non-Repetitive Surge Current (I
TM
)
This is the maximum peak current which may be applied for
an 8/20µs impulse, with rated line voltage also applied,
without causing device failure. (See Figure 2)
For example, the model number for a 7mm epoxy coated
Varistor rated at 440V RMS is V07E440. (Note that this
number will be abbreviated to accommodate marking (laser
branding) of the Varistor body. (The part number brand is
shown in the Device Ratings and Characteristics table.)
Maximum Non-Repetitive Surge Energy (W
TM
)
This is the maximum rated transient energy which may be
dissipated for a single current pulse at a specified impulse
and duration (2ms), with the rated V
RMS
applied, without
causing device failure.
Nominal Voltage (V
N(DC)
)
This is the voltage at which the device changes from the off
state to the on state and enters its conduction mode of
operation. This voltage is characterized at the 1mA point and
has specified minimum and maximum voltage levels.
Clamping Voltage (V
C
)
This is the peak voltage appearing across the MOV when
measured at conditions of specified pulse current amplitude
and specified waveform (8/20µs).
Ordering Information
To order devices in the UltraMOV Series, the base part number must be appended with lead form, packaging and lead space
options as shown below.
V
DEVICE FAMILY:
Harris Varistor
XX
E
XXX
LX
X
X
NONSTANDARD LEAD SPACING OPTIONS:
Blank: Standard lead spacing (see Dimensions Table)
5: 5mm Lead Spacing
7: 7.5mm Lead Spacing
1: 10mm Lead Spacing
DISC DIAMETER:
07, 10, 14, or 20 (mm)
ENCAPSULATION:
E = Epoxy
V
M(AC)RMS
:
130 to 625 (V)
LEAD FORMATION:
L1: Straight
L2: Crimped
L3: In-Line
L4: Trim/Crimp
(Bulk pack only)
PACKAGING:
B: Bulk Pack
T: Tape and Reel
A: Ammo Pack
UltraMOV™ is a trademark of Harris Corporation
All Harris Semiconductor products are manufactured, assembled and tested under
ISO9000
quality systems certification.
Harris Semiconductor products are sold by description only. Harris Semiconductor reserves the right to make changes in circuit design and/or specifications at any time
without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Harris is believed to be accurate
and reliable. However, no responsibility is assumed by Harris or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may
result from its use. No license is granted by implication or otherwise under any patent or patent rights of Harris or its subsidiaries.
For information regarding Harris Semiconductor and its products, call
1-800-4-HARRIS
or see web site http://www.semi.harris.com
4-15
Go Upload

* Only PDF files are allowed for upload

* Enter up to 200 characters.