G1-233P-85-1.8
| Model | G1-233P-85-1.8 |
| Description | Processor Series Low Power Integrated x86 Solution |
| PDF file | Total 247 pages (File size: 4M) |
| Chip Manufacturer | NSC |
Geode™ GX1 Processor Series
Processor Programming
(Continued)
3.3.1.4 EFLAGS Register
The EFLAGS register contains status information and con-
trols certain operations on the GX1 processor. The lower
16 bits of this register, referred to as the EFLAGS register,
is used when executing 8086 or 80286 code. Table 3-4
gives the bit formats for the EFLAGS register.
Table 3-4. EFLAGS Register
Bit
31:22
21
20:19
18
Name
RSVD
ID
RSVD
AC
Flag Type
--
System
--
System
Description
Reserved:
Set to 0.
Identification Bit:
The ability to set and clear this bit indicates that the CPUID instruction is
supported. The ID can be modified only if the CPUID bit in CCR4 (Index E8h[7]) is set.
Reserved:
Set to 0.
Alignment Check Enable:
In conjunction with the AM flag (bit 18) in CR0, the AC flag deter-
mines whether or not misaligned accesses to memory cause a fault. If AC is set, alignment
faults are enabled.
Virtual 8086 Mode:
If set while in protected mode, the processor switches to virtual 8086 oper-
ation handling segment loads as the 8086 does, but generating exception 13 faults on privi-
leged opcodes. The VM bit can be set by the IRET instruction (if current privilege level is 0) or
by task switches at any privilege level.
Resume Flag:
Used in conjunction with debug register breakpoints. RF is checked at instruc-
tion boundaries before breakpoint exception processing. If set, any debug fault is ignored on
the next instruction.
Reserved:
Set to 0.
Nested Task:
While executing in protected mode, NT indicates that the execution of the cur-
rent task is nested within another task.
I/O Privilege Level:
While executing in protected mode, IOPL indicates the maximum current
privilege level (CPL) permitted to execute I/O instructions without generating an exception 13
fault or consulting the I/O permission bit map. IOPL also indicates the maximum CPL allowing
alteration of the IF bit when new values are popped into the EFLAGS register.
Overflow Flag:
Set if the operation resulted in a carry or borrow into the sign bit of the result
but did not result in a carry or borrow out of the high-order bit. Also set if the operation resulted
in a carry or borrow out of the high-order bit but did not result in a carry or borrow into the sign
bit of the result.
Direction Flag:
When cleared, DF causes string instructions to auto-increment (default) the
appropriate index registers (ESI and/or EDI). Setting DF causes auto-decrement of the index
registers to occur.
Interrupt Enable Flag:
When set, maskable interrupts (INTR input pin) are acknowledged and
serviced by the CPU.
Trap Enable Flag:
Once set, a single-step interrupt occurs after the next instruction completes
execution. TF is cleared by the single-step interrupt.
Sign Flag:
Set equal to high-order bit of result (0 indicates positive, 1 indicates negative).
Zero Flag:
Set if result is zero; cleared otherwise.
Reserved:
Set to 0.
Auxiliary Carry Flag:
Set when a carry out of (addition) or borrow into (subtraction) bit position
3 of the result occurs; cleared otherwise.
Reserved:
Set to 0.
Parity Flag:
Set when the low-order 8 bits of the result contain an even number of ones; other-
wise PF is cleared.
Reserved:
Set to 1.
Arithmetic
Carry Flag:
Set when a carry out of (addition) or borrow into (subtraction) the most significant
bit of the result occurs; cleared otherwise.
17
VM
System
16
RF
Debug
15
14
13:12
RSVD
NT
IOPL
--
System
System
11
OF
Arithmetic
10
DF
Control
9
8
7
6
5
4
3
2
1
0
IF
TF
SF
ZF
RSVD
AF
RSVD
PF
RSVD
CF
System
Debug
Arithmetic
Arithmetic
--
Arithmetic
--
Arithmetic
www.national.com
46
Revision 1.0
